Pali Campion

Category Poles

Description

Steel sheet welded columns with polygonal cross section for middle and low tensions overhead lines, manufactured under certified quality check according to  ISO9001 by company ENEL approved and authorised as processing centre according to DM 14/01/08

Manufactured in one section obtained by cold forming of trapezium of pressed steel plate grade according to  EN 10025 and subsequent external longitudinal welding carried out by approved automatic process (submerged arc) and welding check according to EN ISO 3834.

Test draught ENEL approved following to the positive result of the draught test required on the document DS 3010 FOR Enel STANDARDIZATION.

Works depending on the type of the column according to standardized schemes Enel DS3010:
scheme 1: throughout hole d.22 and top cover
scheme 2: M16 nut  earth device, throughout hole  d.22 and top cover with bush on top of the column

Identification mark punched on the plate, quoting manufacturer’s name, columns code, and year of manufacturing

Tolerances on dimensions DS3010 - UNI EN 10051

Protection against corrosion by means of hot dip galvanization obtained with the following cycle: degreasing; pickling, washing, fluxing, pre heating; hot dip galvanization in melted zinc bath at 440÷450°, with minimum percentage of zinc into the bath 98.5%. Coating obtained according to UNI EN ISO 1461 with minimum thickness 55 microns et average 70 microns.

For columns type L; A; B, an external bituminous coating is provided which consists in the application on the galvanized column of a fiberglass bituminous sheath having an height of 500 mm and located at a distance of 0.12H from the base. For the other type of columns this bituminous coating is not provided but it may be applied upon request.

DIMENSIONS

TYPE	HEIGHT (m)	BASE DIAMETER (mm)	TOP DIAMETER (mm)	STEEL THICKNESS (mm)	WEIGHT (kg)	STEEL GRADE	T1
10L10	10	225	100	3	121	S235JR	270
9A10	9	235	100	3	112	S235JR	330
10A10	10	250	100	3	130	S235JR	331
9B14	9	275	140	3	139	S235JR	442
10B14	10	290	140	3	150	S235JR	445
12B14	12	260	140	3	180	S355JO	461
9C15	9	285	150	3	147	S355JO	662
10C15	10	300	150	3	168	S355JO	683
12C115	12	300	150	3.5	234	S355JO	671
9D15	9	290	150	3.5	171	S355JO	877
10D15	10	310	150	3.5	199	S355JO	878
12D15	12	335	150	3.5	253	S355JO	882
9E15	9	360	150	3.5	199	S355JO	1320
10E15	10	380	150	3.5	230	S355JO	1320
12E17	12	425	170	3.5	311	S355JO	1325
9F15	9	385	150	4	237	S355JO	1763
10F15	10	410	150	4	275	S355JO	1763
12F17	12	455	170	4	371	S355JO	1767
10G24	10	475	240	4.5	397	S355JO	2655
12G24	12	525	240	4.5	509	S355JO	2658
12H24	12	620	240	6	754	S355JO	5012

T1 = Test draught applied at a distance of 10cm from top column
Note: Test draught or the oretic collapse draught is the value that generates a diagram of bending moments which approximates in favour of security (coefficient 2 - CEI 11-4), the diagram of the beding moment generated from the comprehensive action due to the conductors and to the wind pressure distributed alone the shaft.